Replacement Tesla Model 3 / Model Y front stabilizer link assembly (right hand),
also known as the front sway bar link or anti-roll bar link. This link connects the front stabilizer bar to the suspension (strut/control arm), transferring roll forces between the left and right sides of the vehicle. Worn stabilizer links are a common source of front-end clunks and play during low-speed maneuvers and over bumps. This right-hand link is a direct-fit replacement for Tesla part number 1188396-00-B on most Model 3 and Model Y variants.
Built using Delphi OE safety technology, this stabilizer link is engineered and tested to OE-level standards:
Validated from below −40 °C to over 120 °C, subjected to up to 720 hours of salt spray, and checked with extensive dimensional and material analysis to ensure excellent compatibility with the original Tesla part. Delphi’s sway bar links are fatigue tested and feature ultrasonic molding to help prevent weld breakage and provide long-term durability.
| PN | Tesla PN 1188396-00-B • Gruber PN 34-TS3-FRSTABLK (Front stabilizer link assembly — RH) |
| OEM description (reference) | FRONT STABILIZER LINK ASSEMBLY RH • Also referred to as front sway bar link / anti-roll bar link (right side) for Model 3 / Model Y. |
| Application | Tesla Model 3 (approx. Jun 2017+ variants) and Tesla Model Y (most 2020+ variants) • front suspension • front stabilizer (sway bar) link — right hand. For vehicles originally equipped with Tesla PN 1188396-00-B. |
| Includes | Complete right-hand front stabilizer link assembly with pre-installed ball joints at both ends, molded rubber dust boots, and installation hardware including locking nuts (no washers included). |
| Condition / grade | New standard replacement stabilizer link built to Delphi OE-style specifications. Non-greasable design with sealed ball joints for long service life. |
| Key dimensions (approx.) | Length: 11.024 in (280.00 mm) • Height: 2.268 in (57.60 mm) • Bar diameter: 0.472 in (12.00 mm). |
| Joint & rod details | Rod type: Suspension rod • End 1 type: Ball joint • End 2 type: Ball joint • Reinforced: No • Dust boot included: Yes • Greasable: No. |
| Materials | Housing material: Steel • Boot material: Rubber • Grade type: Standard Replacement. |
| Hardware & interface | Hardware included: Yes • Locking nuts included: Yes • With spanner attachment: No • Wrench size: T40. |
| Weight / quantity | Approximate weight: 1.576 lb • Required quantity: 1 per vehicle (right-hand link). For best results, replace left and right links at the same time. |
| Position | Front Right (passenger side on left-hand-drive vehicles) • Front suspension stabilizer (sway bar) link. |
| Compatibility notes | Tesla has used multiple stabilizer link revisions on Model 3 / Model Y. Always match the part number stamped on your original right-hand link (1188396-00-B) and verify by VIN/build date. Left-hand and right-hand links are not interchangeable; order the correct side, or replace both as a matched pair. Contact us if you need help confirming fitment before ordering. |
Stabilizer links should typically be replaced in pairs (left and right) to keep roll stiffness balanced and prevent future noise from the opposite side. After installation, road test over small bumps and low-speed turns to confirm that clunks and rattles are gone. While you are there, inspect the front stabilizer bar bushings and other control
arms for wear so you can address any remaining sources of noise or looseness.
Not sure if your Model 3 or Model Y uses this exact front stabilizer link? Check the part number on the original right-hand link or provide your VIN, model year, and build date. We can help confirm that this 1188396-00-B / 34-TS3-FRSTABLK assembly is the correct match for your vehicle before you order.
